SMB Direct
I am trying to utilize SMB Direct ( SMB over RDMA) on some of my Windows 2012 severs using IB. Does anyone have any directions, links, or advice?
View ArticleRe: SMB Direct
What is the problem? Did you look here? https://community.mellanox.com/docs/DOC-2260
View ArticleRe: SMB Direct
There are some helpful links there, but it mostly talks about RoCE. I have to servers with connect x-3 cards. They have SMB multichannel and SMB Direct enabled. From some of the directions I've seen...
View Articledigital optical monitoring
Hello, Is there a Digital Optical Monitoring command (DOM) that is available on the sx1012 switch? Thanks,Daniel
View ArticleRe: SMB Direct
Can you share the configuration, connectivity and so on.Are the servers connected back to back? what is the topology? Are the servers with PCI gen 3 x8? Tuned to performance? Thanks,Ophir.
View ArticleRe: digital optical monitoring
what do you mean by that? to find the transceiver type? if so, run switch (config) # show interface ethernet x/x transceiver See HowTo Find Cable Info on Mellanox Adapters and Switches
View ArticleRe: digital optical monitoring
Ophir, Yes, I found that command but what I mean is Cisco has a similar command "show interfaces transceiver" that show more details about dBm (Tx and Rx Power) and more by enabling the ports as...
View ArticleRe: digital optical monitoring
Hi Daniel.no, only the command I mentioned to show the transceiver type. Thanks,Ophir.
View ArticleClik here to view.
Re: Counters per VF?
Hi Adit,A fix for this issue was intoroduced in mlnx ofed 3.1-1.0.0 and it is also available in upstream kernel since 4.3. Eran.
View ArticleHow to dump mellanox connectx 3 libvma traffic with tcpdump?
or if I cant do it with tcpdump, how I can do it?
View ArticleFirmware for ConnectX-3 Cards with ISL PSIDs
Hello, This is my first post and I couldn't find any reference to my question. I have several ConnectX-3 cards I am trying to upgrade the firmware on. Specifically they are CX354A cards with P/N...
View ArticleInfiniband SX6036G/SX6018F and QLogic HP BLc 4X QDR IB Switch
Hi all, I'm really new to IB, and I'm having some issues while trying to configure my existing IB network with SX6036G gw and SX6018F switches to a new HP Enclosure with QLogic HP BLc 4X QDR IB Switch...
View Articlesx1012 link issue
Hi, So I have two new sx1012 connected to each other with fiber from two different buildings. They both have the same transceivers: [standalone: master] # show interfaces ethernet transceiverPort 1/1...
View ArticleRe: sx1012 link issue
We dont support third party LR4 or SR4 modules. That doesn't mean we do anything to prevent it from working but it may not work. If you provide us the length of the fiber in between, we can suggest a...
View ArticleRe: sx1012 link issue
Hi Anand, Here is the link for LR4 support:LR4 Support on Mellanox Switches It says:Here is the list of Mellanox switches and ports that supports LR4 module (Long Reach - QSFP), OPN: MC2210511-LR4 up...
View ArticleRe: sx1012 link issue
Hi Anand, If use 1012, which ports support Mellanox LR4 module? Thanks a lot.
View ArticleRe: How to enable wake-on-la (wol) on a mellanox InfiniBand card ?
Hello, I have ConnectX 2 card and WOL is not working either. Its running latest firmware 2.9.1200. Its not working in Linux and Windows either.Can some one help me out on this? Thanks!
View ArticleClik here to view.
Re: sx1012 link issue
Addition question about that connection: Is there some mode that I need to configure on the port to be aware that it is a Ethernet connection and not IB? Thank you,Daniel
View Article