Re: Question about Dual SX6036G configurations on vSphere 6.0 Update 2
Hi Jea-Hoon, Q1. Why ARP-Proxy mode enabled then IB SM was disabled? this is by design - SM can't run on the same switch where proxy-arp can run - this is documented in the MLNX-OS user manual Q2....
View ArticleRe: Question about Dual SX6036G configurations on vSphere 6.0 Update 2
Thank you for your quick exact reply...:) I know also default partition must be enable on fabric. But security reason I want to disable IPoIB function on default partition, not default partition...
View ArticleRe: Question about Dual SX6036G configurations on vSphere 6.0 Update 2
Hi, Try the below - I never tried it but it's available: switch(config)# no ib partition Default ipoib force
View ArticleClik here to view.
Re: Question about Dual SX6036G configurations on vSphere 6.0 Update 2
Okay!I tried your command via my iPhone with VPN.But force option wasn't accepted to MLNX-OS.I think if there is a modification on default partition then MLNX-OS apply the modification to all othere...
View ArticleClik here to view.
Re: ping is not happening between MCX314A and MCX354A 40G Etherenet slots
Hi!MCX354A is Infiniband HCA and MCX314A is Ethernet only Adapter.If you install Infiniband driver and MCX354A, you must change Ethernet mode then you will pining to MCX314A end-to-end connection...
View ArticleGetting this error in Oracle Linux 6.8 under /var/log/message || kernel:...
Hi Everyone, We are getting below error in one of physical server, Which makes the server inaccessible from remote because we getting disconnect frequently, Regarding this we have raised a SR with...
View ArticleFirmware number mismatch for...
Hi, I am trying to install a driver for DEL1090001019. When I install the firmware ( http://www.mellanox.com/downloads/firmware/fw-ConnectX3-rel-2_35_5100-01T7NW-Flexboot-3.4.648.bin.zip ) as...
View ArticleClik here to view.
Re: Question about Dual SX6036G configurations on vSphere 6.0 Update 2
Hi , I would suggest opening a support ticket with Mellanox support@mellanox.com
View ArticleRe: Atomics with EDR cards
Hello, Yes, it should contain userspace support for these functions. Please refer to the RDMA programming user manual :...
View ArticleRe: Firmware number mismatch for...
Hello Pedro, Could you please invoke ibstat or ibv_devinfo so we can see the current firmware version installed on your card? Thank you, Karen.
View ArticleRe: Above 4G issue
Not sure to what specific "....above 4G fix" you are referring but if you are pointing at InfiniBand ability to link under Windows, when MMIO is assign to above 4GB then basically, over native 64 bit...
View ArticleRe: Firmware number mismatch for...
In addition, there is a new firmware version available for your card 2.36.500 please test again with the new firmware:http://www.mellanox.com/page/firmware_table_dell?mtag=oem_firmware_download
View ArticleRe: Question about Dual SX6036G configurations on vSphere 6.0 Update 2
Unfortunately my 2 of SX6036G's warranty was out in last year.I always saw your PB before purchase your products.But always PB's function was beta or slowest driver support in historical.I will use...
View ArticleQSFP to SFP+ splitting and configuring IP addresses on subports
Hi, I have used a Mellanox QSFP to SFP+ splitting cable to split my QSFP interface to four SFP+ on my SX1012 switch. I want to know if its possible to assign an IP address on these sub ports (SFP+) on...
View ArticleRe: How to configure infiniband connectX-3 on to Kernel based Virtual Machine...
Do you get any error while adding virtual function device to VM? When VM is up and running, what can you see in 'lspci' output?
View ArticleRe: MCX354A-FCBT & Switch Speed Issue
Hello, please see this community document: https://community.mellanox.com/docs/DOC-1460 Your adapter, switch and cable are all 56Gb capable. With the show license command on the switch do you see a...
View ArticleRe: Centos 6.7 + MT25208 InfiniHost III Ex
Hi AI, These HCA cards have been EOL since 12/01/2011 & EOS since 11/01/2013.Older Mellanox OFED driver version would not support the current OS RHEL 6.7.This would as well be applicable with OFED...
View ArticleClik here to view.
Issue with Mellanox Connect-X3 Pro cards
Hi, We are using Mellanox Connect-X3 PRO card for our solution.We are facing some problem with dual port configuration. Below are the configuration done for dual port. sdn@ubuntu:~$ cat...
View ArticleMLNX_OFED_LINUX RHEL 6.8
Hi. I'm working with upgrading our HPC environment from RHEL 6.6 to RHEL 6.8 (due to security reason) and therefore have the following question:Is there a package of MLNX_OFED_LINUX-3.2-2 for RHEL 6.8...
View ArticleRe: Firmware number mismatch for...
Hello Pedro, Thank you for informing us regarding the issue, we removed the previous bin file and uploaded the correct one:http://www.mellanox.com/page/firmware_table_dell_archiveBest regards,Karen.
View Article