Re: Connect-X4 says it doesn't support LINK_TYPE_P1 configuration
That makes sense, but why is ibv_devinfo reporting that the transport is Infiniband?
View ArticleClik here to view.
Re: Voltaire 500EX-D. Mellanox MHGH28-XTC(DDR) or MHEH28-XTC(SDR)?
Thank you eddie.notz!I did not think so many vendor documents provided wrong information.
View ArticleRe: Red Hat 6.7 + NFS over RDMA
Hi Team,As per the below link, we configured the setup. and able to mount the NFS mount points over RDMA.HowTo Configure NFS over RDMA (RoCE) But in log file, constantly we are getting below mention...
View ArticleRe: How to get port counters separately for each channel ?
I think there may be a terminology issue here. When you write switch, do you mean some chassis based switch ? Chassis based switches (commonly anything larger than 36 or 38 4x switch ports) is a...
View ArticleClik here to view.
Re: Disable cipher suite zero or limit access to the IPMI service
Hi Yairi, I´m using VOLTAIRE 4036. Thanks, Francisco 2016-06-16 9:20 GMT-03:00 yairi <community@mellanox.com>: Mellanox Interconnect...
View ArticleRe: SN2700 LACP not working
Hi Jurgen, I'm assuming LACP with SN2700 vs. a hyperv doesn't work in your setup and not as a general statement. 1. can you please provide the SN2700 software version: "show version"2. output of...
View ArticleClik here to view.
Re: How to get port counters separately for each channel ?
Hello Hal. Thanks for answer.What you describe - this is clear. Apparently I'm very bad explain. I try again to describe my problem. By the switch i mean, for example, SX6025If i have one (for example...
View ArticleTrouble with ConnectX-3 VPI VFs with SR-IOV
Hi, I am trying to get VFs working on the IB card to pass through to KVM guests. Following through the steps in HowTo Configure SR-IOV for ConnectX-3 with KVM (InfiniBand), I get in trouble after...
View ArticleRe: Disable cipher suite zero or limit access to the IPMI service
Hi Francisco, I am not a great expert with Cipher Suite Zero but i am not sure how that has to do with the 4036 switch. that switch has no IPMI. what exactly do you need (or in other words, what the...
View ArticleRe: How to get port counters separately for each channel ?
There are no standardized counters for traffic statistics by (source, destination) so that you can see specific counters only for traffic between say n1 port 1 and n3 port 1. In terms of determining...
View ArticleRe: Disable cipher suite zero or limit access to the IPMI service
Hello Francisco,It sounds like your question is irrelevant, since the Voltaire 4036 switch doesn't utilize IPMI. Do you agree?It seems there is no related vulnerability with this switch.
View Articlehow do I configure Mellanox sn2700 to connect to a 40Gb port on a RS8264 switch?
I have three SB2700's to connect to the 40Gb ports on a RS 8264 switch. I don't know how to configure the up-link to the 40gb ports. Thanks
View ArticleRe: How to get port counters separately for each channel ?
I do exactly as you sayI had thought that there is perhaps there are still other ways Thanks for your reply
View ArticleClik here to view.
Re: Disable cipher suite zero or limit access to the IPMI service
Hi all, The Voltaire has support a IPMI, when i send a ipmi command, i receive a response, follow the exemplo:
View ArticleRe: passthru MT27500 ConnectX-3 SR-IOV via kvm-qemu cause host Redhat 6.4 crash
Hi Delsun FooSorry for late because I am on business trip these days.I don't know if your issue is solved , but, From the filemlx4_core 0000:1b:00.0: Bad or unreadable EEPROM on port 1Do you try...
View ArticleClik here to view.
Re: Disable cipher suite zero or limit access to the IPMI service
Hmmm, what version software is on the Voltaire switch ("version show")?
View ArticleRe: how do I configure Mellanox sn2700 to connect to a 40Gb port on a RS8264...
HI,I haven't tested RS8264 switch connectivity with Spectrum. however simply try to change the port speed on the relevant port to 40G run (for example on interface eth 1/1): switch (config) # interface...
View ArticleRe: how do I configure Mellanox sn2700 to connect to a 40Gb port on a RS8264...
Ok thank you I will try that. But are there any special instruction I have to give to make the connectivity happen? I only have experience with Cisco and Brocade switch.
View Article