Re: Re: Re: ISR9024D-M
Sweet Im in and able to manage the switch vi the infiniband connection. The issue was that one of the nics on the box has the same subnet as the switch (192.168.2.x). The SM on the switch itself is...
View ArticleRe: Infiniband network in mixed environment (Windows/Linux)
Thanks a lot! This answer was exactly what I was looking for. Von: justinclift Gesendet: Mittwoch, 26. Juni 2013 00:49An: Wolfheimer, FelixBetreff: Re: - Infiniband network in mixed environment...
View ArticleRe: Infiniband network in mixed environment (Windows/Linux)
Yes, this is completely possible and also reasonably common. IP over IB (IPoIB) is well supported in several OS's, including Linux (Red Hat/CentOS/SL/Debian/etc), Windows, VMware ESX, and Solaris....
View ArticleRe: voltaire 4036 cant connect to CLI
the reset button will not factory default that switch. the only way to factory default is from the CLI.you have to get this console working somehow!!
View ArticleRe: voltaire 4036 cant connect to CLI
4036 console cable line order is different with Broadcom, Cisco.I found D-Link serial console cable is compatible with 4036. If you can purchase the serial DB9 to RJ45 connector check below. 1. Your...
View ArticleRe: vSphere 5.1 U1 IPoIB VLAN support
Hi inbusiness,The way of VLAN configuration for IPoIB on vSphere 4.x/5.x didn't change.I suspect that you may have the wrong configuration on 5.x. Can you please provide more information.- Subnet...
View ArticleRe: Getting eIPoIB to work ?
Hi drolfe,I'm trying too to get eipoib to work on ubuntu 12.04. In the end, did you succeed to have eipoib working? Can you add your infiniband hca as an interface for a bridge device? I'm stuck in...
View ArticleRe: vSphere 5.1 U1 IPoIB VLAN support
* Here it is...------------------------------------------------------------------------------------------------------------------~ # esxcfg-vswitch -lSwitch Name Num Ports Used Ports Configured...
View ArticleClik here to view.
Re: voltaire 4036 cant connect to CLI
Yes, You're right~! Push the reset button for long time that just revert admin password to default "123456". I was confused. To: justyk31011 I'm so sorry for my mistake...I think that you must get a...
View ArticleRe: IPoIB not working on Windows 2008 r2 - need help
On you initial posting you mentioned something around..."ping is working for few seconds and then stops" and then you also mentioned that you CAN see it in your Ethernet network and your (other IP...
View ArticleGetting dual ConnectX EN adapters (MNPH29B-XTC) to work
Hello all, I picked up a few Connect-X EN MNPH29B-XTC adapters but running into some issues. I am trying to install 2 of these into my storage server but one of them seems to work at a time. If I...
View ArticleRe: Infiniband Performance Analysis?
It appears one of the cards was in a PCI Gen 2 X4 slot. After putting it in a PCI Gen 3 X4 slot it went up to 35 Gbps via netperf.
View ArticleRe: Getting eIPoIB to work ?
www.mellanox.com/page/products_dyn?product_family=26 First start with the mellanox driver 2.0 which now has support for ubuntu out of the box the binary path issue should be fixed in the next release...
View ArticleMHRH2A-XSR firmware assistance
I have an MHRH2A-XSR card that has firmware 2.9.1200 but there is no board ID when running the following command “flint -d mt26418_pci_cr0 query”. Is that normal and if so, how can I update the...
View ArticleClik here to view.
Invalid module format when loading ib_* (RHEL 6.4)
I installed RHEL 6.4 and upgraded. The current kernel is 2.6.32-358.11.1. Thus I also updated MLNX_OFED_LINUX-2.0-2.0.5-rhel6.4-x86_64.iso with mlnx_add_kernel_support.sh. My command line...
View ArticleClik here to view.
XenServer support
Hello. This is crossposted at XenServer ( Infiniband support ). I see ( http://www.mellanox.com/page/osv_support_ib ) that Infiniband is supported on XenServer 6.1.0. Will be supported on 6.2.0 ?Can I...
View ArticleRe: Getting dual ConnectX EN adapters (MNPH29B-XTC) to work
Hi Jibesh Do the cards actually come up or are they dead?
View ArticleRe: Getting dual ConnectX EN adapters (MNPH29B-XTC) to work
The cards show up in Device Manager but one will have an error on it that shows device cannot be started. The other card will be operational. If I disable the operational card in Device Manager, I am...
View ArticleRe: Getting eIPoIB to work ?
Unfortunately I have an Infinihost device with chipset MT23108.. From release notes I understood that it is deprecated from mlnx 1.5.3 onward ... see below release notes for 2.0, 1.5.3 and 1.5.2 Does...
View Article