Clik here to view.
4036E software update
Hello, I have a 4036E switch and I am trying to update the software. Here is the system info:The health monitor shows:The update software chassis gives:with each .fpf being identical to the one on the...
View ArticleClik here to view.
Responder QCE errors
Attempting to setup RoCE with windows server 2012. I need to verify the SMB direct/RDMA is working end to end. I am seeing RDMA traffic on windows perf counters, but I am getting Responder QCE errors...
View ArticleRe: Installation of MLNX_OFED_LINUX-2.3-2.0.0 fails on ubuntu 14.04 x86_64
It seems like your compilation of the OFED kernel modules failed. Can you provide make.log from /var/lib/dkms/mlnx-ofed-kernel/2.3/build/ ? Thanks,--Shachar
View ArticleRe: Re: Installation of MLNX_OFED_LINUX-2.3-2.0.0 fails on ubuntu 14.04 x86_64
Sure, please see attached
View ArticleRe: Re: Installation of MLNX_OFED_LINUX-2.3-2.0.0 fails on ubuntu 14.04 x86_64
Seems like your configure script for the modules were run with incorrect parameters (i.e. ./configure without any parameters, which results in nothing being built). Did you attempt any manual...
View ArticleRe: Installation of MLNX_OFED_LINUX-2.3-2.0.0 fails on ubuntu 14.04 x86_64
no, i did no installation customization or changes to the environment.I opened tgz and ran "sudo ./mlnxofedinstall".
View ArticleRe: Firmware for MT_04A0110001?
Answering myself: Firmware for Volataire 500 EX-D can be found here: Firmware for ConnectX® - Mellanox Technologies. Look for MHEH28-XTC (PSID: MT_04A0110001)The problem with "Modify QP error" and...
View ArticleFirmware for Voltaire 500 EX-D (PSID: MT_04A0110001)?
I can't figure out what firmware to use for MT_04A0110001 (Voltaire 500 EX-D dual port). The information of the device is listed as: Image type: FS2FW Version: 2.7.700Device ID:...
View ArticleRe: Responder QCE errors
Maybe this will help: Deploying Windows Server 2012 with SMB Direct (SMB over RDMA) and the Mellanox ConnectX-2/ConnectX-3 using InfiniBand. Check the PowerShell commands from section 6 (i.e. "Verify...
View ArticleClik here to view.
Re: Responder QCE errors
Thank you for your reply.I know this document well. I have set my server and clients up according to it. I have flow-control setup on my extreme 670 switch and the ports tagged. I just cannot establish...
View ArticleRe: Installation of MLNX_OFED_LINUX-2.3-2.0.0 fails on ubuntu 14.04 x86_64
Hi Igor,Please sent the output of the command below on your server:# dkms status -m "mlnx-ofed-kernel" -v "2.3" Did you try to run the installation on other servers with the same OS? Thanks,Vladimir
View ArticleRe: Installation of MLNX_OFED_LINUX-2.3-2.0.0 fails on ubuntu 14.04 x86_64
Hi Vladimir, same result on other server with same OS and identical HW. Provided "dkms" command returns without any output. # dkms status -m "mlnx-ofed-kernel" -v "2.3"#
View ArticleRe: Installation of MLNX_OFED_LINUX-2.3-2.0.0 fails on ubuntu 14.04 x86_64
Hi Igor,Can you arrange a remote access to one of your servers?
View ArticleRe: Installation of MLNX_OFED_LINUX-2.3-2.0.0 fails on ubuntu 14.04 x86_64
I will check if that is possible, it may take time anyway.Is there anything else I can do? Any debug flags, logs?
View ArticleRe: ib_ep.c:297 MXM ERROR failed to create address handle: Cannot allocate...
Hi,Could you open a support case?The support team will follow up from there. Thanks,Ophir.
View ArticleRe: ib_ep.c:297 MXM ERROR failed to create address handle: Cannot allocate...
Enable IPv6 support on the hosts by running command: echo 0 > /proc/sys/net/ipv6/conf/enp131s0/disable_ipv6
View ArticleRe: ib_ep.c:297 MXM ERROR failed to create address handle: Cannot allocate...
ipv6 is already enabled for the hosts.
View ArticleRe: ib_ep.c:297 MXM ERROR failed to create address handle: Cannot allocate...
Opir, does MXM work with ROCE? Our setup at University of Houston is ROCE. I beginning to suspect that MXM is strictly meant for infiniband protocol, any taughts before I formerly engage the support...
View ArticleRe: ib_ep.c:297 MXM ERROR failed to create address handle: Cannot allocate...
MXM can use Ethernet layer, but it doesn't use RoCE.
View ArticleClik here to view.
Re: ib_ep.c:297 MXM ERROR failed to create address handle: Cannot allocate...
Please, e-mail me and let's continue via e-mail.
View Article