Below is the command lists on PPC-Boot mode (Not safe mode)...
PPCBoot 1.1.6 (Nov 16 2004 - 08:21:51)
CPU: IBM PowerPC 440 Rev. C
Board: Artesyn Technologies PM/PPC-440gp
Artesyn Monitor Version 1.5.0
VCO: 800 MHz
CPU: 400 MHz
PLB: 133 MHz
OPB: 66 MHz
EPB: 66 MHz
I2C: ready
DRAM: ECC Init ................Done 512 MB
FLASH: 64 MB
Initializing board as Monarch....
Scanning for PCI devices....
Scanning PCI devices on bus 0
LOCALE VEND DEV REV BASE1 BASE2 BASE3 BASE4 BASE5
------- ---- ---- --- -------- -------- -------- -------- -------- --------
00,0d,0 10b5 9056 ba 80000000 b0800000 80200000 80400000 ........ ........
In: serial
Out: serial
Err: serial
Net: EMAC0, EMAC1
BEDBUG:ready
Hit any key to stop autoboot: 0
=> clear
Unknown command 'clear' - try 'help'
=> help
as - assemble memory
autoscr - run script from memory
base - print or set address offset
bdinfo - print Board Info structure
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
bootd - boot default, i.e., run 'bootcmd'
break - set or clear a breakpoint
cmp - memory compare
coninfo - print console devices and informations
continue- continue from a breakpoint
cp - memory copy
crc32 - checksum calculation
date - get/set/reset date & time
dhcp - invoke DHCP client to obtain IP/boot params
ds - disassemble memory
echo - echo args to console
erase - erase FLASH memory
flinfo - print FLASH memory information
getdcr - Get an IBM PPC 4xx DCR's value
go - start application at address 'addr'
help - print online help
imd - i2c memory display
imm - i2c memory modify (auto-incrementing)
inm - memory modify (constant address)
imw - memory write (fill)
icrc32 - checksum calculation
iprobe - probe to discover valid I2C chip addresses
iloop - infinite loop on address range
isdram - print SDRAM configuration information
iminfo - print header information for application image
irqinfo - print information about IRQs
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loop - infinite loop on address range
md - memory display
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
next - single step execution, stepping over subroutines.
nm - memory modify (constant address)
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rdump - Show registers.
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setdcr - Set an IBM PPC 4xx DCR's value
setenv - set environment variables
sleep - delay execution for some time
where - Print the running stack.
step - single step execution.
tftpboot- boot image via network using TFTP protocol
and env variables ipaddr and serverip
version - print monitor version
? - alias for 'help'
pci_enum - Enumerates and displays PCI Bus Enumeration Info
pci_info - Displays PCI Bus Enumeration Info
prog_i2c - Programs default i2c bootstrap settings
moninit - Copies PPCBoot monitor into Soldered Flash
monship - Erases soldered flash, inits environment variables
initenv - Initializes Board Environment variables
um - destructive memory test
=>