Re: Windows 2012 RDMA Storage Options
Assuming your adapters are capable of using Infiniband or RoCE - try using samba 4.0 (supports SMB-direct) that shares filesystem between Linux & WindowsIt is an open source implementation of SMB...
View ArticleRe: mlnx-en-3.2-1.0.1.1 installation blues
Hi, My PSID: HP_0F60000010Could this be used to check if my card is ConnectX or ConnectX-2? TIA,Nikos
View ArticleRe: How can I change the protocol per HCA On same ESXi 6 host?
Thank you for your answer.I'm made a VPI Gateway with my 2 of SX6036G FDR Gateway systems on vSphere environment today.Test was successful.This system works like charm with Untangle 12 that running on...
View ArticleClik here to view.
boot problem SX6512
I have a SX6512 with two management modules and upon booting it appears to boot fine (which I watched through the consoles). The problem is whenever I ssh to it or http to it I get the following...
View ArticleRe: boot problem SX6512
Try to remove one of the mgmt modules. I would start with mgmt module #2
View ArticleRe: How can I find SX6036G Switch GUID on CLI?
The one node license means that the license is only for one switch. Once the license is installed on the switch it supports up to 648 ports.
View ArticleClik here to view.
Atomics with EDR cards
I want to know if verbs-level atomics (fetch_and_add, compare_and_swap) are supported with the following EDR card? CA 'mlx5_0' CA type: MT4115 Number of ports: 1 Firmware version: 12.14.2036...
View ArticleClik here to view.
Re: Ethernet Switch: which MIB to read for learned unicast MAC addresses?
Hi Ophir, Marina, Any news on this? Thanks again,Dan
View ArticleHow to configure infiniband connectX-3 on to Kernel based Virtual Machine (KVM)
Hi All, i am trying to configure IB0 virtual interface on KVM. I have enabled SR-IOV on my bios, also VT-d is enabled. installed with MLNX_OFED updated verionsFirmware on CA is also updated with...
View ArticleRe: MLNX_OFED Update for kernel 3.19 in Ubuntu 14.04.3
Hi, does anyone know how I can contact Mellanox for this issue? Thanks
View ArticleClik here to view.
ConnectX-2 EN Digital Optical Monitoring
Some SFP+ modules exports diagnostics.On Linux this can be retrieved by the "ethtool -m|--dump-module-eeprom|--module-info" command (see Re: Optics (SFP) monitoring on ixgbe and igbe — Linux Network...
View ArticleClik here to view.
ConnectX-2 CQE remote access error (Protection Error on remote data buffer)...
Dell hardware running Oracle Solaris 11.3 serving as a storage appliance: Kernel version: SunOS 5.11 11.3Entire Version : 0.5.11-0.175.3.4.0.5.0System Type: Dell PowerEdge R730xdpci bus 0x0081 cardnum...
View ArticleWhat is the status of addressing CVE-2016-4565
This CVE is quite important as it affects (afaict) all or nearly all Infiniband stacks (from distribution specific, to OFED, to MOFED). Status is that the public PoC allows writing of arbitrary kernel...
View ArticleRe: Windows-Linux ConnectX-2 setup
Hello Matthew, Trying running "ib_write_bw" again but specify the ib-device and "rdma_cm". Also, you can you use flag "--report_gbits"Please see example below.# ibdev2netdevmlx4_0 port 1 ==> ib0...
View ArticleMellanox Switch SNMP Polling for Transfer Rates
I am setting up an ELK stack (Elasticsearch, Logstash, Kibana) on my Ubuntu 14.04.3 LTS server for monitoring, including SNMPv3 & V2c. This server will monitor roughly 200 6036 switches. I am able...
View ArticleClik here to view.
Centos 6.7 + MT25208 InfiniHost III Ex
Hi Guys, I would really appreciate some help installing MT25208 InfiniHost III Ex driver on Centos 6.7. My configuration:# lspci | grep fini06:00.0 InfiniBand: Mellanox Technologies MT25208 InfiniHost...
View Article