Clik here to view.
Re: F-X430044 24 port DDR switch factory reset and firmware update
Hi Bob, The F-X430044 is a Flextornics OEM switche.Please contact Flextronics representatives:Michael.Dolkin@il.flextronics.com Tomer.Fridman@il.flextronics.com
View ArticleClik here to view.
Re: Is it possible to switch ConnectX-3 VPI into Ethernet mode in Solaris 11.1?
I have ConnectX-3 Ethernet (not VPI) MCX384A-BCAA. It's working in Windows 2012R2 and Linux ubuntu as 40 GB connection. It shows 10GB connection in Solaris and not connected. According to the thread,...
View ArticleRe: Is it possible to switch ConnectX-3 VPI into Ethernet mode in Solaris 11.1?
As far as I know nothing was changed since last year, better ask Oracle support or other users with the same setup
View ArticleRe: Getting hardware timestamping from the NIC.
Hi, I believe the latest addition to the ethernet driver - 2.3 and 2.4 have support for receive side time-sampling and their corresponding user manual has examples on how to enable it for a socket....
View ArticleRe: ethtool self diagnostic failed
Can you attach the full dmesg output once you reload your driver (mlx4_core, mlx4_en) ? Any chance to move this card to a different server / PCI slot and re-check ?
View ArticleClik here to view.
Re: looking for mlx4_en.ko for ppc64p7 for Fedora 20
Hi, I don't see any releases for fedora20 which are not for x86 architecture on the Mellanox website including previous older releases. I would say that it doesn't exist.
View ArticleRe: Getting hardware timestamping from the NIC.
Hi, I used the mellanox user manual to enable the TCP socket to get the time stamp according the steps explained in the section 3.1.10 Time-Stamping in the manual. The problem is that the from the...
View ArticleAbout ConnectX-3 MT27500 family
According to VMware Compatibility Guide, ConnectX-3 MT27500 supports VMware 4.x and 5.x.In this case, can I understand ConnectX-3 MT27500 family includes MCX353A-QCBT?
View ArticleRe: ethtool self diagnostic failed
Hi, I can move the slots, but when another card was installed in another system with Fedora,the self test gave the same answer after the firmware / driver were upgraded. If you think it is worth...
View ArticleMCX354A-FCBT does not show "Port Protocol" tab in device manager after FW...
After upgrading my MCX354A-FCB_A1 network adapters to FW 2.33.5100 the "Port Protocol" tab in the Windows 7 device manager is not available anymore(it was before), as shown in the ConnectX®-3 VPI...
View ArticleClik here to view.
connectx 2 eth mode between two hosts with passive copper cable
Hello, I've put connectx 2 adapters into eth mode on two hosts, and connected them with a passive copper cable (QSFP). The link state comes up but I cannot get any connectivity between the hosts. ib...
View ArticleRe: About ConnectX-3 MT27500 family
Hi FerberThanks for the prompt response.Is this adapter also MT27500 family?
View ArticleRoCE multicast issue: why mckey could only work in roce_mode=1 when IGMP...
Here's the backgrounds:: NIC card: Mellanox Technologies MT27500 Family [ConnectX-3] Mellanox OFED driver: OFED.2.4.0.1.2 O.S: Red Hat Enterprise Linux Server release 7.0 Based on the above...
View ArticleRe: RoCE multicast issue: why mckey could only work in roce_mode=1 when IGMP...
I believe RoCE multicast ONLY works on RoCE1.5 & 2.0, and supports IGMPv2
View ArticleCan I do L3 with SX1018HP switches?
Hi,I have four SX1018HP switches in two different C7000 chassis from HP. I want to configure MLAG on two switches but the command "ip routing" is not available. The firmware versión is 3.4.0000.How can...
View Article40GE Cisco compatibility question
Dear community members!Qe intend to install MCX353A-FCBT 40G Ethernet card in DELL servers, toconnect the servers to Cisco DC switches.The data sheet I have found...
View ArticleClik here to view.